Netgear WNDAP330 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Vernetzung Netgear WNDAP330 herunter. Netgear WNDAP330 Reference Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 7
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Version 1.0
Layer 2 / Layer 3 switches and multi-SSID multi-VLAN network with traffic
separation
This document describes the steps to undertake in configuring a Layer 2/Layer 3 switch (in this
document a FMS7382S with firmware 7.3.1.7) and a WNDAP330 to host a multi-SSID and multi-
VLAN network.
The solution will allow separating the Wireless traffic and Wired traffic of each of the VLANs
configured, from any other VLAN which will exist on the Wired or Wireless LAN.
The diagram below shows a typical scenario.
VLAN
2
VLAN
3
LAYER2/LAYER3 SWITCH
VLAN1:
Management IP 192.168.0.254
Port: 1/0/1, 1/0/6, 1/0/7-1/0/28 (Untagged)
VLAN 2:
Ports: 1/0/2, 1/0/3 (PVID = 2, Untagged), 1/0/6 (Tagged)
VLAN 3:
Ports: 1/0/4, 1/0/5 (PVID = 3, Untagged) , 1/0/6 (Tagged)
WNDAP330
Management VLAN = 1
Management IP = 192.168.0.235
SSID “VLAN2(VLAN ID = 2), Open system None
SSID “VLAN3(VLAN ID = 3), Open system None
LAN to 1/0/6
DGFV338 LAN to 1/0/2
Internet
DGFV338
LAN IP: 10.0.0.1/24
DHCP 10.0.0.0/24
1/0/4 to LAN
Corporate LAN
Seitenansicht 0
1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1 - Version 1.0

Version 1.0 Layer 2 / Layer 3 switches and multi-SSID multi-VLAN network with traffic separation This document describes the steps to undertake

Seite 2

Version 1.0 Table of Contents NETWORK SETUP ...

Seite 3

Version 1.0 NETWORK SETUP Physical setup DGFV338 connected to port 1/0/2 on Layer2/Layer3 switch Corporate LAN connected to port 1/0/4 on

Seite 4

Version 1.0 LAYER2/LAYER3 SWITCH CONFIGURATION Create a new VLAN Access the VLAN configuration via Switching, VLAN, Basic. Input the

Seite 5

Version 1.0 Save the configuration Access the Save Config page via Maintenance. Tick the box appearing within the Save Configuration option

Seite 6

Version 1.0 ACCESS POINT CONFIGURATION Enable the Wireless Radio mode and configure the Radio Channel Enable the Radio (by default its turne

Seite 7

Version 1.0 FURTHER NOTES Testing Testing can be performed by connecting a Wireless client to each of the SSID alternatively (i.e. VLAN2, VLAN3) a

Kommentare zu diesen Handbüchern

Keine Kommentare