Netgear WC7520 Bedienungsanleitung Seite 15
- Seite / 213
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Introduction and Overview
15
ProSafe 20-AP Wireless Controller WC7520
The WC7520 wireless controller system supports the following access point models:
• NET
GEAR WNAP210 ProSafe wireless-N access point
• NET
GEAR WNAP320 ProSafe wireless-N access point
• NET
GEAR WNDAP350 ProSafe dual-band wireless-N access point
• NET
GEAR WNDAP360 ProSafe dual-band wireless-N access point
Future releases will support additional access point models.
NETGEAR ProSafe Access Points
You can connect access points to the wireless controller either directly with an Ethernet cable
through a router or switch, or remotely through an IP network. After you have used the
automatic discovery process and added access points to the managed access point list on
the wireless controller, the wireless controller converts the standard access points to
dependent access points by pushing firmware to the access points. From then on, you can
centrally manage and monitor the access points.
A WC7520 wireless controller system can support the following access points:
• WNAP2
10 ProSafe Wireless-N Access Point
- Sup
ports 802.11b, 802.11g, and 802.11n network devices
- Sup
ports Power over Ethernet (PoE) with a power consumption of up to 5.8W
- Req
uires minimum firmware version WNAP210_2.0.8 or a newer version.
For product documentation and firmware, see
http://support.netgear.com/app/products/model/a_id/8101.
• WNAP3
20 ProSafe Wireless-N Access Point
- Sup
ports 802.11b, 802.11g, and 802.11n network devices
- Sup
ports Power over Ethernet (PoE) with a power consumption of up to 5.8W
- Accep
ts optional antennas
- Req
uires minimum firmware version WNAP320_2.0.7 or a newer version.
For product documentation and firmware, see
http://support.netgear.com/app/products/model/a_id/18601.
• WNDAP35
0 ProSafe Dual Band Wireless-N Access Point
- Sup
ports 802.11a, 802.11b, 802.11g, and 802.11n network devices
- Sup
ports PoE with a power consumption of up to 10.75W
- Con
current operation in 2.4 GHz and 5 GHz radio band while in 802.11n mode
- Accep
ts optional antennas
- Requires minimum firmware version WNDAP350
_V2.0 or a newer version.
For product documentation and firmware, see
http://support.netgear.com/app/products/model/a_id/12823.
- ProSafe 20-AP Wireless 1
- Controller WC7520 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Table of Contents 4
- Chapter 12 Troubleshooting 7
- Introduction and Overview 10
- Package Contents 11
- Hardware Features 12
- Rear Panel Features 13
- Figure 3 14
- NETGEAR ProSafe Access Points 15
- Plan a Wireless Network 16
- Firmware 16
- Organize the Network 16
- Licenses 18
- Maintenance and Support 18
- Figure 4 19
- Figure 5 21
- Figure 6 21
- Basic and Advanced Settings 22
- Profile Groups 23
- Advanced Profile 24
- Figure 9 25
- Scenarios 27
- DHCP Server 29
- Figure 10 33
- Deployment Scenarios 34
- Prerequisites 36
- RF Planning 41
- To define a building: 42
- Figure 14 43
- Figure 15 43
- To edit a building: 44
- To delete a building: 45
- Figure 16 45
- Figure 17 47
- Figure 18 48
- Figure 19 49
- Access Point Discovery and 51
- Management 51
- Limitations after Discovery 53
- Run the Discovery Wizard 54
- Figure 21 55
- Figure 22 55
- Discovery Results 56
- Manage the Access Point List 57
- Item Description 58
- Figure 26 60
- Configuring Network Settings 63
- Time Management 64
- Figure 29 65
- Table 9. Time settings 65
- Management VLANs 66
- Manage the DHCP Server 67
- 2. Click Add 68
- To edit a DHCP server: 69
- To delete a DHCP server: 69
- Manage Certificates 70
- Configure Syslog Settings 71
- To configure alarm actions: 72
- Figure 34 72
- 3. Click App 73
- Small WLAN Networks 75
- Larger WLAN Networks 75
- Profile Naming Conventions 76
- Figure 36 77
- Figure 37 78
- Figure 38 84
- Setting Description 85
- Figure 39 86
- Figure 40 86
- Figure 41 88
- Configurations 90
- Configure the Radio 91
- Figure 43 92
- Configure Wireless Settings 93
- Table 20. Wireless settings 94
- Figure 45 97
- Configure Channels 99
- Allocation screen displays: 100
- Specify RF Management 101
- Basic RF Management 102
- Figure 47 103
- Figure 48 104
- Figure 49 106
- Configure Load Balancing 107
- Figure 50 108
- Configure Rate Limiting 109
- Figure 51 110
- Figure 52 110
- Security 112
- Manage Rogue Access Points 113
- Figure 53 114
- Figure 54 116
- To use an external ACL: 118
- Figure 55 119
- Figure 56 121
- Server Groups 122
- Figure 57 123
- 4. Click Apply to save 124
- Figure 58 125
- Manage Guest Network Access 126
- Figure 59 127
- Table 29. Portal settings 128
- Figure 60 129
- Figure 61 130
- Figure 62 130
- Figure 63 130
- 4. Conf 131
- 6. Click Clo 133
- Maintaining the Controller 135
- Figure 64 136
- To upgrade the firmware: 137
- Figure 65 137
- 5. Click Apply 138
- Figure 66 140
- Reboot Access Points 141
- Manage External Storage 141
- Manage Remote Access 142
- Figure 69 143
- Table 32. SNMP settings 143
- Specify Session Time-Outs 144
- Save the Logs 144
- View Alerts and Events 145
- To view system alerts: 146
- Figure 73 146
- To view RF events: 146
- Figure 74 147
- Figure 75 147
- Figure 76 148
- Figure 77 148
- Figure 78 148
- Manage Licenses 149
- 1. Select Ma 150
- Settings screen displays: 150
- Register Your Licenses 151
- Figure 81 152
- Retrieve Your Licenses 153
- Manage Stacking 154
- Configure Stacking 155
- Figure 83 156
- Figure 84 156
- Table 35. Stacking settings 156
- Controller Selection List 157
- Manage Redundancy 158
- Figure 87 159
- N:1 Redundancy 160
- Figure 90 162
- Figure 91 163
- Figure 92 163
- Configure Redundancy 164
- Components 167
- To monitor the network: 168
- Figure 94 168
- View Network Usage 170
- Figure 96 171
- Figure 99 174
- Figure 100 174
- View Clients in the Network 176
- Figure 102 177
- Figure 103 178
- Figure 104 180
- Figure 105 182
- Figure 108 184
- Figure 109 184
- Figure 110 185
- Figure 111 187
- Figure 112 188
- To view the guest list: 189
- Figure 113 189
- Figure 114 189
- Monitor the SSIDs 190
- Monitor the Clients 191
- View Blacklisted Clients 192
- To export the list of blac 193
- Troubleshooting 194
- Test LED Never Turns Off 195
- LAN Port LEDs Not On 195
- Ethernet Cabling 195
- IP Address Configuration 195
- Internet Browser 196
- Request timed out 197
- Problems with Date and Time 198
- Problems with Access Points 198
- Connection Problems 199
- To ping an access point: 200
- Figure 119 200
- Figure 120 201
- Specifications 202
- WC7520 data sheet at 203
- Notification of Compliance 205
- GPL License Agreement 207
- Numerics 208
Verwandte Produkte und Handbücher für Vernetzung Netgear WC7520
Vernetzung Netgear DG834GSP Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung Netgear 3G Bedienungsanleitung
(106 Seiten)
(106 Seiten)
Vernetzung Netgear 7000 Series Bedienungsanleitung
(220 Seiten)
(220 Seiten)
Vernetzung Netgear 724TP Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Vernetzung Netgear MA401 Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Vernetzung Netgear DG834GUV5 Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Vernetzung Netgear WMS5316 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
(2 Seiten)
Vernetzung Netgear MA111v2 Betriebsanweisung
(83 Seiten)
(83 Seiten)
Vernetzung Netgear 782S Schnellstart Anleitung
(48 Seiten)
(48 Seiten)
Vernetzung Netgear Switch M4100 Bedienungsanleitung
(559 Seiten)
(559 Seiten)
Vernetzung Netgear DG834G Bedienungsanleitung
(190 Seiten)
(190 Seiten)
Vernetzung Netgear WPNT121 Betriebsanweisung
(48 Seiten)
(48 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern