Netgear WC9500 Bedienungsanleitung Seite 134
- Seite / 357
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Manage Security Profiles and Profile Groups
134
ProSAFE Wireless Controller WC9500
Legacy 802.1x None To configure legacy 802.1x authentication:
1. Set up and enable an internal or external (RADIUS or LDAP)
authentication server.
For information, see
Manage Authentication Servers and
Authentication Server Groups on page 136.
2. Select the Local or External radio button.
3. If you select the External radio button, select the
authentication server that you wish to use from the menu.
WPA with Radius TKIP
TKIP + AES
To configure WPA authentication with a RADIUS server:
1. Set up and enable an internal or external (RADIUS or LDAP)
authentication server.
For information, see
Manage Authentication Servers and
Authentication Server Groups on page 136.
2. From the Data Encryption menu, select the type of
encryption:
- TKIP. Supports T
emporal Key Integrity Protocol (TKIP)
only.
- TKIP +
AES. Supports both TKIP and Advanced
Encryption Standard (AES).
3. Select the Local or External
radio button.
4. If you select the External radio button, select the
authentication server that you wish to use from the menu.
WPA2 with Radius AES
TKIP + AES
To configure WPA2 authentication with a RADIUS server:
1. Set up and enable an internal or external (RADIUS or LDAP)
authentication server.
For information, see
Manage Authentication Servers and
Authentication Server Groups on page 136.
From the Data Encryption menu, select the type of
encryption:
- AES. Supports
AES only.
- TKIP + AES. Supports both TKIP and AES.
2. Select the Local or External
radio button.
3. If you select the External radio button, select the
authentication server that you wish to use from the menu.
Table 6. Network authentication and data encryption settings (continued)
Network Authentication
Selection
Data
Encryption
Options
Configuration Steps
- ProSAFE Wireless Controller 1
- Compliance 2
- Trademarks 2
- Revision History 2
- Contents 4
- Register the Licenses 5
- Chapter 13 Troubleshooting 9
- Introduction 11
- Key Features and Capabilities 12
- Package Contents 14
- Hardware Features 14
- Table 1. LED functions 15
- Back Panel Features 16
- Figure 4. Product label 17
- Supported NETGEAR Antennas 21
- Licenses 23
- Maintenance and Support 23
- Scenarios 24
- Profile Group Concepts 26
- System Planning Concepts 28
- Client VLANs 29
- DHCP Server 29
- RF Planning and Deployment 45
- RF Planning Overview 46
- Add a Building and Floors 49
- Scale a Floor 53
- Add a WiFi Obstruction Area 58
- Change the Name of a Building 61
- Duplicate a Single Floor 62
- Remove a Single Floor 63
- Signal strength at 68
- 6. Click the floor name 70
- The floor map displays 70
- 7. Click the AP 70
- Access points 82
- Overview 84
- Manage the Time Settings 94
- Management VLAN Concepts 95
- Untagged VLAN Concepts 96
- Link Aggregation Concepts 96
- Manage the DHCP Server 98
- Add a DHCP Server 99
- 5. Click the Add button 100
- Remove a DHCP Server 102
- Register Your Licenses 103
- 7. Click the Apply button 104
- The changes are saved 104
- To register your licenses: 105
- Manage Certificates 107
- Settings 108
- Configure Syslog Settings 110
- 6. Click the Apply button 111
- To configure alarm actions: 112
- Setting Description 113
- Manage Security Profiles and 115
- Profile Groups 115
- Small WLAN Networks 116
- Large WLAN Networks 117
- Profile Naming Conventions 117
- Add an Advanced Profile Group 124
- Server Groups 136
- Import a MAC List from a File 145
- Discover and Manage Access 152
- General Discovery Guidelines 153
- Layer 3 Discovery Guidelines 153
- Points in a Layer 2 Subnet 154
- Manage the Managed AP List 163
- Configure Wireless and QoS 172
- Concepts 173
- Configure the Radio 173
- Configure Wireless Settings 176
- Profile Group 186
- Configure Channels 188
- Radio Frequency Concepts 191
- WLAN Healing Concepts 192
- Manage the Preferred Bands 198
- Quality of Service Concepts 200
- 8. Click the Apply button 203
- Manage Load Balancing 204
- Configure Load Balancing 205
- Manage Rate Limiting 206
- Manage Rogue Access Points 212
- Classify Rogue Access Points 214
- 00:00:11:11:22:29 216
- 00:00:11:11:22:28 216
- 00:00:11:11:22:27 216
- 00:00:11:11:22:26 216
- 00:00:11:11:22:25 216
- Manage Guest Network Access 217
- Configure a Portal 218
- User and Account Concepts 222
- Add a Management User 223
- Add a WiFi User 224
- Add a Captive Portal Account 226
- 6. Click the Add button 227
- Add a Captive Portal User 230
- Remove Users or Accounts 236
- Upgrade the Firmware 241
- To upgrade the firmware: 242
- Reset the Wireless Controller 245
- Manage External Storage 246
- Manage Remote Access 247
- Specify Session Time-Outs 249
- Manage the System Logs 250
- Save the System Logs 252
- View Alerts and Events 253
- View System Alerts 254
- View Radio Frequency Events 255
- View Load-Balancing Events 256
- View Rate-Limit Events 257
- To view rate-limit events: 258
- View Redundancy Events 259
- View Stacking Events 260
- Manage Licenses 261
- Retrieve Your Licenses 263
- Reboot Access Points 264
- The default number is 69 266
- Stacking Concepts 269
- Configure a Stack 271
- VRRP Redundancy Concepts 278
- VRRP ID 123 279
- VRRP N:1 Redundancy Concepts 282
- Change a Redundant Controller 287
- Remove a Redundancy Group 289
- Monitor the Network 291
- To view the Usage screen: 308
- To view the Clients screen: 315
- Does Not Manage 321
- Item Description 322
- Controller 324
- Wireless Controller Manages 325
- 12. Click the OK button 336
- Troubleshooting 337
- Power LED Is Not Lit 338
- Status LED Never Turns Off 338
- Check the Ethernet Cabling 339
- Check the Internet Browser 340
- Resolve Discovery Problems 342
- Resolve Connection Problems 342
- Ping an Access Point 343
- • Factory Default Settings 346
- • Technical Specifications 346
- • Password Requirements 346
- Factory Default Settings 347
- Technical Specifications 348
- Password Requirements 349
- Numerics 351
Verwandte Produkte und Handbücher für Vernetzung Netgear WC9500
Vernetzung Netgear GSM7228PS Bedienungsanleitung
(799 Seiten)
(799 Seiten)
Vernetzung Netgear WG111 Bedienungsanleitung
(77 Seiten)
(77 Seiten)
Vernetzung Netgear WNA1100 Bedienungsanleitung
(48 Seiten)
(48 Seiten)
Vernetzung Netgear CM212 Bedienungsanleitung
(19 Seiten)
(19 Seiten)
Vernetzung Netgear WG103 Anwendungshinweis
(6 Seiten)
(6 Seiten)
Vernetzung Netgear WN111v2 Betriebsanweisung
(56 Seiten)
(56 Seiten)
Vernetzung Netgear WGE101 Bedienungsanleitung
(17 Seiten)
(17 Seiten)
Vernetzung Netgear DG834Gv5 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Vernetzung Netgear GA311 Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Vernetzung Netgear WNA1000 Betriebsanweisung
(58 Seiten)
(58 Seiten)
Vernetzung Netgear RH340 Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Vernetzung Netgear WMS5316 Bedienungsanleitung
(70 Seiten)
(70 Seiten)
Vernetzung Netgear DG834 V3 Bedienungsanleitung
(168 Seiten)
(168 Seiten)
Vernetzung Netgear GA302T Bedienungsanleitung
(62 Seiten)
(62 Seiten)
Vernetzung Netgear WC7600 Bedienungsanleitung
(307 Seiten)
(307 Seiten)
Vernetzung Netgear WG111T Bedienungsanleitung
(49 Seiten)
(49 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.181 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern