Netgear WG302v1 Bedienungsanleitung Seite 77
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
NETGEAR ProSafe 802.11g Wireless Access Point WG302 Reference Manual
Advanced Configuration 4-5
v4.0, April 2006
4. Click Apply to enable the Advanced Wireless Settings.
Wireless Bridge and Repeater Modes
The ProSafe 802.11g Wireless Access Point lets you build large bridged wireless networks or
simply act as a Repeater. For example, the choices are:
• Client Access Point to Access Point. This is the default setting for the WG302.
• Point-to-Point Bridge. In this mode, the WG302 will communicate ONLY with another
Bridge-mode Wireless Station. You must enter the MAC address (physical address) of the
other Bridge-mode Wireless Station in the field provided. WEP can (and should) be used to
protect this communication (see “Configuring a Point-to-Point Bridge” on page 4-6).
• Multi-Point Bridge. Select this only if this WG302 is the “Master” for a group of Bridge-
mode Wireless Stations. The other Bridge-mode Wireless Stations must be set to Point-to-
Point Bridge mode, using the MAC address of the WG302. All traffic is then sent to this
“Master”, rather than communicating directly with each other. WEP can (and should) be used
to protect this traffic (see “Configuring a Multi-Point Bridge” on page 4-7).
• Repeater. If selected, the WG302 will operate as a Repeater only, and will send all traffic to
the remote access point. The MAC address (physical address) of the remote AP must be
entered (see“Configuring Wireless Repeater Mode” on page 4-9).
These screen used to configure these options are located by selecting Access Point Settings under
Advanced on the main menu (see Figure 4-4).
Beacon Interval Specifies the data beacon rate between 20ms and 1004ms..
DTIM Interval The Delivery Traffic Indication Message specifies the data beacon rate
between 1 and 255. The default is 1.
Preamble Type A long transmit preamble may provide a more reliable connection or
slightly longer range. A short transmit preamble gives better performance.
Long is the default
Antenna Select the desired antenna for transmitting and receiving. Auto is the
default.
Table 4-1. Advanced Wireless LAN Settings Fields (continued)
Field Description
- NETGEAR ProSafe 802.11g 1
- Wireless Access Point 1
- WG302 Reference Manual 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Radio Frequency Notice 2
- FCC Statement 3
- , May 12, 2006 4
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 14
- Chapter 1 17
- Introduction 17
- Key Features and Standards 18
- Introduction 1-3 19
- 1-4 Introduction 20
- System Requirements 21
- Package Contents 21
- Hardware Description 22
- 5. Power Socket 24
- Chapter 2 25
- Cabling Requirements 26
- Default Factory Settings 26
- 6HFXULW\2SWLRQV 27
- 5DQJH8SWR)RRW5DGLXV 27
- Figure 2-2 29
- Figure 2-3 30
- Figure 2-4 31
- Figure 2-5 32
- Setting Basic IP Options 33
- Figure 2-7 34
- Configuring Wireless Settings 35
- Figure 2-8 36
- Figure 2-9 40
- Figure 2-10 46
- Setting up A Security Profile 47
- Figure 2-12 48
- Figure 2-13 50
- Figure 2-14 51
- Figure 2-15 52
- Figure 2-16 53
- Figure 2-17 54
- Figure 2-18 55
- Figure 2-19 56
- Chapter 3 59
- Management 59
- 3-2 Management 60
- CLI Commands 61
- 3-4 Management 62
- Figure 3-3 62
- To access the General screen: 63
- 3-6 Management 64
- Management 3-7 65
- 3-8 Management 66
- Figure 3-5 66
- Table 3-2. Statistics Fields 66
- Management 3-9 67
- Figure 3-6 67
- 3-10 Management 68
- Figure 3-7 68
- Configuration File Management 69
- 3-12 Management 70
- Management 3-13 71
- Figure 3-9 71
- 3-14 Management 72
- Chapter 4 73
- Advanced Configuration 73
- 4-2 Advanced Configuration 74
- Figure 4-1 74
- Hotspot Settings 75
- Advanced Wireless Settings 75
- 4-4 Advanced Configuration 76
- Figure 4-3 76
- Advanced Configuration 4-5 77
- 4-6 Advanced Configuration 78
- Figure 4-4 78
- Advanced Configuration 4-7 79
- Figure 4-5 79
- 4-8 Advanced Configuration 80
- Figure 4-6 80
- Advanced Configuration 4-9 81
- Figure 4-7 81
- 4-10 Advanced Configuration 82
- Chapter 5 83
- Troubleshooting 83
- The LAN light is not lit 84
- Troubleshooting 5-3 85
- 5-4 Troubleshooting 86
- Appendix A 87
- Factory Defaults and 87
- Technical Specifications 87
- Technical Specifications 89
- Appendix B 91
- Related Documents 91
- B-2 Related Documents 92
- Appendix C 93
- Command Line Reference 93
- C-6 Command Line Reference 98
Verwandte Produkte und Handbücher für WLAN-Zugangspunkte Netgear WG302v1
(28 Seiten)
(43 Seiten)
WLAN-Zugangspunkte Netgear WG102 Bedienungsanleitung
(110 Seiten)
(110 Seiten)
WLAN-Zugangspunkte Netgear WAC120 Datenblatt
(3 Seiten)
(3 Seiten)
WLAN-Zugangspunkte Netgear WG102 Bedienungsanleitung
(118 Seiten)
(118 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern