Netgear WC7600 Bedienungsanleitung Seite 203
- Seite / 307
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Maintain the Wireless Controller and Access Points
203
ProSAFE Wireless Controller WC7600
WARNING:
When you click the Apply button and the Now radio button is
selected to upgrade the firmware immediately, do not try to go
online, turn off the wireless controller, shut down the computer, or
do anything else to the wireless controller until the wireless
controller finishes rebooting. When the Status LED turns green,
wait a few more seconds before you do anything.
7. Click the Apply button.
Unless you scheduled the firmware upgrade for a particular time, the firmware is
upgraded immediately, and the wireless controller reboots.
8. (Optional) Verify that the wireless controller is running the latest firmware:
a. Select Monitor > Network > Controller.
The Controllers screen displays.
b. Verify the firmware version in the Version column.
Server Parameters section (TFTP and FTP only)
Server IP Enter the IP address of the TFTP or FTP server.
File Name Enter the file name of the firmware.
User Name (FTP only) Enter the user name to access the FTP server.
Password (FTP only) Enter the password to access the FTP server.
Boot Information section
Active Partition This field is an informational field that displays the active partition and the
current firmware version.
Boot Partition to Upgrade Select the radio button for the partition to which the new firmware should be
saved.
After upgrade boot from Select the radio button for the partition from which the wireless controller
should reboot after the firmware has been upgraded.
Schedule section
Schedule Update Status This field is an informational field that displays when the firmware upgrade
occurs. If no update is scheduled, the field displays None.
When to Upgrade? Select when the firmware upgrade should occur:
• Later. Make selections from the menus to specify the date and time when
the upgrade should occur.
• Now. The upgrade occurs immediately after you click the Apply button.
Setting Description
- ProSAFE Wireless Controller 1
- Compliance 2
- Trademarks 2
- Chapter 1 Introduction 3
- Chapter 3 RF Planning 3
- Chapter 13 Troubleshooting 8
- Passwords Requirements 8
- Key Features and Capabilities 10
- Introduction 11
- Hardware Features 12
- Package Contents 12
- Table 1. LED functions 13
- Back Panel Features 14
- Figure 4. Product label 15
- NETGEAR ProSAFE Access Points 16
- Licenses 20
- Maintenance and Support 20
- Scenarios 21
- Profile Group Concepts 23
- Management VLAN 25
- Client VLANs 26
- DHCP Server 26
- RF Planning 41
- To define a building: 42
- Figure 12 43
- Figure 13 43
- To edit a building: 44
- To delete a building: 45
- Figure 14 46
- Figure 15 47
- Figure 16 49
- Figure 17 49
- Overview 51
- Manage the Time Settings 61
- Management VLAN Concepts 62
- Untagged VLAN Concepts 63
- Link Aggregation Concepts 63
- Manage the DHCP Server 65
- 5. Click the Add button 67
- Remove a DHCP Server 69
- Register Your Licenses 70
- To register your licenses: 72
- Manage Certificates 74
- Configure Syslog Settings 77
- To configure alarm actions: 79
- Manage Security Profiles and 82
- Profile Groups 82
- Small WLAN Networks 83
- Large WLAN Networks 84
- Profile Naming Conventions 84
- Add an Advanced Profile Group 91
- Server Groups 104
- Import a MAC List from a File 112
- 00:00:11:11:22:26 113
- 00:00:11:11:22:25 113
- Discover and Manage Access 119
- General Discovery Guidelines 120
- Layer 3 Discovery Guidelines 120
- Number of Controllers Octet 121
- 1 controller 02:04 121
- 2 controllers 02:08 121
- 3 controllers 02:0c 121
- Limitations after Discovery 122
- Points in a Layer 2 Subnet 123
- Manage the Managed AP List 131
- Item Description 132
- Manage Rogue Access Points 140
- Classify Rogue Access Points 142
- 00:00:11:11:22:29 144
- 00:00:11:11:22:28 144
- 00:00:11:11:22:27 144
- Manage Guest Network Access 145
- Configure a Portal 146
- 7. Click the Apply button 148
- User and Account Concepts 150
- Add a Management User 151
- Add a WiFi User 152
- Add a Captive Portal Account 154
- 6. Click the Add button 155
- Add a Captive Portal User 156
- Remove a User or Account 159
- Configure Wireless and QoS 161
- Settings 161
- Concepts 162
- Configure the Radio 162
- Configure Wireless Settings 165
- Profile Group 175
- Configure Channels 177
- Radio Frequency Concepts 180
- WLAN Healing Concepts 181
- Manage the Preferred Bands 186
- Quality of Service Concepts 188
- 8. Click the Apply button 191
- Manage Load Balancing 192
- Configure Load Balancing 193
- Manage Rate Limiting 194
- Manage the Configuration File 199
- Upgrade the Firmware 201
- Reset the Wireless Controller 205
- Manage External Storage 206
- Manage Remote Access 207
- 6. Click the Apply button 208
- Specify Session Time-Outs 209
- Manage the System Logs 209
- Query the System Logs 210
- Save the System Logs 212
- Clear the System Logs 212
- View Alerts and Events 213
- View Radio Frequency Events 214
- View Load-Balancing Events 215
- View Rate-Limit Events 217
- View Redundancy Events 218
- View Stacking Events 218
- Manage Licenses 219
- View Your Licenses 220
- Retrieve Your Licenses 222
- Reboot Access Points 223
- Setting Description 225
- The default number is 69 225
- Stacking Concepts 228
- Configure a Stack 230
- VRRP Redundancy Concepts 237
- Before failover 238
- After failover 239
- VRRP N:1 Redundancy Concepts 241
- Figure 24 243
- Figure 25 243
- Figure 26 244
- Change a Redundant Controller 246
- Remove a Redundancy Group 247
- Its Components 248
- Monitor the Network 249
- To view the Usage screen: 266
- To view the Clients screen: 273
- Does Not Manage 279
- Controller 282
- Wireless Controller Manages 283
- 10. Click the Cancel button 294
- Troubleshooting 295
- Power LED Is Not Lit 296
- Status LED Never Turns Off 296
- Check the Ethernet Cabling 297
- Check the Internet Browser 298
- Resolve Discovery Problems 300
- Resolve Connection Problems 300
- Ping an Access Point 301
- • Factory Default Settings 304
- • Technical Specifications 304
- • Password Requirements 304
- Factory Default Settings 305
- Technical Specifications 305
- Password Requirements 306
Verwandte Produkte und Handbücher für Vernetzung Netgear WC7600
Vernetzung Netgear WG111T Bedienungsanleitung
(49 Seiten)
(49 Seiten)
Vernetzung Netgear 597E Betriebsanweisung
(49 Seiten)
(49 Seiten)
Vernetzung Netgear WG511T Betriebsanweisung
(48 Seiten)
(48 Seiten)
Vernetzung Netgear 597E Betriebsanweisung
(12 Seiten)
(12 Seiten)
Vernetzung Netgear WC7520 Bedienungsanleitung
(213 Seiten)
(213 Seiten)
Vernetzung Netgear DG834GSP Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung Netgear 3G Bedienungsanleitung
(106 Seiten)
(106 Seiten)
Vernetzung Netgear 7000 Series Bedienungsanleitung
(220 Seiten)
(220 Seiten)
Vernetzung Netgear 724TP Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Vernetzung Netgear MA401 Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Vernetzung Netgear DG834GUV5 Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Vernetzung Netgear WMS5316 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
(2 Seiten)
Vernetzung Netgear MA111v2 Betriebsanweisung
(83 Seiten)
(83 Seiten)
Vernetzung Netgear 782S Schnellstart Anleitung
(48 Seiten)
(48 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.558 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern