Netgear WNDAP380Rv2 Bedienungsanleitung Seite 138
- Seite / 152
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Command-Line Reference
138
ProSAFE Dual Band Wireless-N Access Point with RFID Support, WNDAP380R
| | | | and wireless mode)
| | | |-channel auto --Set wireless channel to auto mode
| | | |-channel-width --Wireless channel width
| | | |-client-isolation --Client isolation status
| | | |-data-rate --Wireless transmission date rate
| | | |-dtim --Wireless DTIM period in beacon interval
| | | |-fragmentation-length --Wireless fragmentation threshold
| | | |-guard-interval --Interval (from interference from other
| | | | transmissions)
| | | |-macacl add --Add wireless access control (ACL)
| | | |-macacl del --Delete wireless access control (ACL)
| | | |-macacl del all --Delete wireless access control (ACL)
| | | | Database
| | | |-max-client --Maximum client
| | | |-power --Output power
| | | |-preamble-type --Wireless preamble (only effect on
| | | | 802.11b rates)
| | | |-rifs-transmission --Enable successive frame transmission
| | | | at different transmit
| | | |-rogue-ap-detection --Enable rogue access point detection
| | | |-rogue-ap-detection knownap add --Add rogue access point detection
| | | |-rogue-ap-detection knownap
del MAC --Delete rogue access point detection
| | | |-rogue-ap-detection knownap del all --Delete rogue access point detection
| | | | Database
| | | |-rts-threshold --Wireless RTS/CTS threshold
| | | |-wds --Wireless Bridge status
| | | |-wds> --Wireless Bridge setting
| | | | |-1 --1st WDS security profile status
| | | | |-1> --1st security profile
| | | | | |-authentication --Authentication type
| | | | | |-authentication
open encryption --Data encryption
| | | | | |-name --Profile name
| | | | | |-remote-mac --Remote MAC
| | | | | |-wep-key --Wireless wep key
| | | | | |-wpa-passphrase --Wireless wpa passphrase
| | | | |
| | | | |-2 --2nd WDS security profile status
| | | | |-2> --2nd security profile
| | | | | |-authentication --Authentication type
| | | | | |-authentication open encryption --Data encryption
| | | | | |-name --Profile name
| | | | | |-remote-mac --Remote MAC
| | | | | |-wep-key --Wireless wep key
| | | | | |-wpa-passphrase --Wireless wpa passphrase
| | | | |
| | | | |-3rd --3rd WDS security profile status
| | | | |-3> --3rd security profile
| | | | | |-authentication --Authentication type
- ProSAFE Dual Band Wireless-N 1
- WNDAP380R 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Monitoring 4
- Chapter 7 Troubleshooting 5
- What Is in the Box? 7
- System Requirements 8
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Introduction 13
- Installation and Basic 14
- Configuration 14
- Ethernet Cabling Requirements 16
- Web Management Interface 19
- To configure time settings: 20
- Configure the IP Settings 21
- Ceiling Installation 31
- Wall Installation 35
- Desk Installation 38
- Wireless Configuration and 39
- Security 39
- Security Profiles 42
- Security Profile Concepts 43
- Form for 802.11b/bg/ng Modes 44
- Form for 802.11a/an Modes 45
- Configure Legacy 802.1X 52
- Figure 11. Legacy 802.1X 53
- Figure 12. WPA with RADIUS 53
- Figure 13. WPA2 with RADIUS 53
- Figure 15. WPA-PSK 54
- Figure 16. WPA2-PSK 54
- Management 63
- Enable Remote Management 64
- Web Browser Upgrade Procedure 67
- TFTP Server Upgrade Procedure 68
- Defaults 69
- Restore the Configuration 70
- Settings 70
- Default Configuration 72
- Enable the Syslog Server 73
- To enable a syslog server: 74
- To configure STP and VLANs: 80
- Configure Hotspot Settings 81
- To set up a hotspot server: 82
- To configure advanced QoS: 86
- 4. Click Apply 87
- Configure Wireless Bridging 88
- Advanced Configuration 100
- Configure RFID Settings 103
- To reboot the RFID module: 106
- To reset the RFID module: 106
- 3. Click Apply 107
- Monitoring 108
- View System Information 109
- Monitor Wireless Clients 111
- View the Activity Log 113
- Traffic Statistics 114
- Troubleshooting 116
- Basic Functioning 117
- Wireless-Capable Computer 118
- Check these items: 119
- Request timed out 121
- Problems with Date and Time 122
- Troubleshoot the RFID Module 122
- Supplemental Information 124
- Technical Specifications 125
- Factory Default Settings 127
- Command-Line Reference 131
- Numerics 147
Verwandte Produkte und Handbücher für WLAN-Zugangspunkte Netgear WNDAP380Rv2
(28 Seiten)
(43 Seiten)
WLAN-Zugangspunkte Netgear WG102 Bedienungsanleitung
(110 Seiten)
(110 Seiten)
WLAN-Zugangspunkte Netgear WAC120 Datenblatt
(3 Seiten)
(3 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern